- 您现在的位置：买卖IC网 > Sheet目录872 > P036T048T12AL (Vicor Corporation)V.I CHIP PRM REGULATOR 48V 120W
Application Information (continued)
OVP – Overvoltage Protection
The output overvoltage protection set point of the P036F048T12AL is
factory preset for 56 V. If this threshold is exceeded the output shuts
down and a restart sequence is initiated, also indicated by PC pulsing.
If the condition that causes OVP is still present, the unit will again shut
V?I Chip Regulator
Adjusting Current Limit
The current limit can be lowered by placing an external resistor
between the I L and SG ports (see Figure 18 for resistor values) . With
the I L port open-circuit, the current limit is preset to be within the
range specified in the output specifications table on Page 4.
down. This cycle will be repeated until the fault condition is removed.
The OVP set point may be set at the factory to meet unique high
voltage requirements.
100
PRM Output Power Versus VTM Output Power
As shown in Figure 17, the P036F048T12AL is rated to deliver 2.5 A
maximum, when it is delivering an output voltage in the range from
26 V to 48 V, and 120 W, maximum, when delivering an output
voltage in the range from 48 V to 55 V. When configuring a PRM for
use with a specific VTM, refer to the appropriate VTM data sheet. The
VTM input power can be calculated by dividing the VTM output power
by the VTM efficiency (available from the VTM data sheet). The input
10
power required by the VTM should not exceed the output power rating
of the PRM.
1
0
0.5
1
1.5
2
2.5
3
Desired PRM Output Current Limit (A)
2.55
2.50
2.45
2.40
Figure 18 — Calculated external resistor value for adjusting current limit,
actual value may vary.
Input Fuse Recommendations
2.35
2.30
2.25
2.20
2.15
0
Safe Operating Area
~ ~
20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
Factorized Bu s Voltage (V f )
A fuse should be incorporated at the input to the PRM, in series with
the +IN port. A fast acting fuse, NANO2 FUSE 451/453 Series 10 A
125 V, or equivalent, may be required to meet certain safety agency
Conditions of Acceptability. Always ascertain and observe the safety,
regulatory, or other agency specifications that apply to your specific
application.
Product Safety Considerations
If the input of the PRM is connected to SELV or ELV circuits, the output
Figure 17 — P036F048T12AL rating based on Factorized Bus voltage
The Factorized Bus voltage should not exceed an absolute limit of
55 V, including steady state, ripple and transient conditions. Exceeding
this limit may cause the internal OVP set point to be exceeded.
Parallel Considerations
The PR port is used to connect two PRMs in parallel to form a higher
power array. When configuring arrays, PR port interconnection
terminating impedance is 10 k to SG. See note Page 8 and refer to
Application Note AN002. Additionally one PRM should be designated
as the master while all other PRMs are set as slaves by shorting their
SC pin to SG. The PC pins must be directly connected (no diodes) to
assure a uniform start up sequence. Consult Vicor applications
engineering for applications requiring more than two PRMs.
of the PRM can be considered SELV or ELV respectively.
If the input of the PRM is connected to a centralized DC power system
where the working or float voltage is above SELV, but less than or
equal to 75 V, the input and output voltage of the PRM should be
classified as a TNV-2 circuit and spaced 1.3 mm from SELV circuitry or
accessible conductive parts according to the requirements of
UL60950-1, CSA 22.2 60950-1, EN60950-1, and IEC60950-1.
Application Notes
For PRM and V?I Chip application notes on soldering, board layout,
and system design please click on the link below:
http://www.vicorpower.com/technical_library/application_information/chips /
Applications Assistance
Please contact Vicor Applications Engineering for assistance,
1-800-927-9474, or email at apps@vicorpower.com.
vicorpower.com
800-735-6200
V?I Chip Regulator
P036F048T12AL
Rev. 1.9
Page 10 of 14
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
P045T048T17AL
V.I CHIP PRM REGULATOR 48V 170W
P045T048T32AL
V.I CHIP PRM REGULATOR 48V 320W
P048T048M24AL
V.I CHIP PRM REGULATOR 48V 240W
P048T048T12AL
V.I CHIP PRM REGULATOR 48V 120W
P081N-271F2CBR10K
POT MODULE 8MM 10K SIDE ADJ
P090L-02T20BR50K
POT ROTARY 50K OHM 9MM SNAPIN
P092N-QC15AR20K
POT ROTARY 20K OHM 9MM
P110KH1-0F25BR10K
POT ROTARY 10K OHM 11MM BUSHING
相关代理商/技术参数
P037253-001
制造商:Superior Electric 功能描述:Auxiliary Equipment - T5587* Paralleling Choke Cpver
P037S
制造商:Pro-Signal 功能描述:TRANSFORMER AUDIO 100V LINE 4W 制造商:PRO SIGNAL 功能描述:TRANSFORMER, AUDIO, 100V LINE, 4W
P037T
制造商:Pro-Signal 功能描述:TRANSFORMER AUDIO 100V LINE 8W 制造商:PRO SIGNAL 功能描述:TRANSFORMER, AUDIO, 100V LINE, 8W
P037U
制造商:Pro-Signal 功能描述:TRANSFORMER AUDIO 100V LINE 16W
P038
制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT | PNP | 300V V(BR)CEO | 500MA I(C) | TO-92
P038
制造商:Pro-Signal 功能描述:TRANSFORMER AUDIO 100V LINE 15W
P0380
制造商:TE Connectivity 功能描述:
P-038347-0082
制造商:Edwards Signaling & Security Systems 功能描述:HORN ASM ATLAS 30W